I ve been reading forums all over the net for 2 weeks and I failed to find solution for my problem. here is my problem;
I am able to receive data from serial port in to richtextbox and its working fine .. what i wanna do is dislay data in textbox by spliting string[code]...
I have serial port object which continuously receiving data from weighing device, which sends data in 0001450= format (8 Bytes). I read about datareceived event, and implement that, but i must use Thred.Sleep to get all data and read with serial.ReadExisting. Does the ReadBytesTreshold=8 raised DataReceived event after 8 bytes of data??
Is there any way to cancel, abort, stop DataReceived event?
I am new to VB2008 Express, I have been trying to get data from the Serial port, i have tried for days to get it working. I have read lots of articles but most seem to be for Console applications and I am using an Application. All I am trying to do is create a form with a Textbox and this should display the data received from the serial port.
The data i am trying to receive is "ABC" on Com1 Can anyone either send me a project, as I am sure its something to do with how i am configuring it, or if thats not possible, show me in code?
i was not getting o/p properly when i tried to receive data from serial port using the following code.
Public Class form1
Private Sub Timer1_Tick(ByVal sender As System.Object, ByVal e As System.EventArgs) Handles Timer1.Tick
If SerialPort1.IsOpen Then
[code]....
I'm trying to control a serial port device that both send and receives data. I can receive data quite happily from the serial port but I don't appear to be able to send data to the device. The device works perfectly as I can test it using putty, I open putty select serial and select 1200 baud, the device immediately lights up and can send and receive. However when the port is set up and opened in VB the device doesn't light up so I can't send data to it but can receive data from it. According to the instructions I need to send either ASCII 'X' Hex '$58' or Decimal '88' to make the device ready.
Code (VB Studio 2005) :-
Public Sub New(ByVal synchronisingObject As ISynchronizeInvoke)
ComPortUsed = My.Computer.Registry.GetValue("HKEY_LOCAL_MACHINESoftwareNJB", "COMUSED", Nothing)
PricePerTrack = My.Computer.Registry.GetValue("HKEY_LOCAL_MACHINESoftwareNJB", "PRICETRACK", Nothing)
Me.synchronisingObject = synchronisingObject
[Code] .....
Opening and closing the port works fine, and as far as i can tell, the serial.write("blahblah") should be writing to the output buffer, but I am unable to test or verify this by reading it in. the commented "Receive data from serial port" and subsequent DoUpdate() function are where i am having trouble. It doesnt seem to actually be reading in the data if it is in fact writing it correctly.
[Code]...
What I am doing is creating an app to send and receive CNC programs to machine tools via the RS232 interface. At the moment I am testing the software with 2 laptops linked together through a cable I have made up. which all works. I have added a serial port to my form 1 and using the code below I can send and receive data. However with the send button I can open the comm port send the data and then close the comm port (No Problems there). With the receive button I want to open the comm port receive the data and close the comm port. The problem I have is checking when the app has finished receiving data so I can then close the comm port
Private Sub Btn_Send_Click(ByVal sender As System.Object, ByVal e As System.EventArgs) Handles Btn_Send.Click
Try
[Code]....
i'm using serial port monitor 4.0. i need to know how to received the data and show in a textbox.
here is how my data look like in the serial port monitor:
40 03 04 05 00 00 00 80 05 04 01 00 00 00 11 00 @......�........
80 07 04 05 00 10 00 01 02 02 14 80 07 04 05 00 �..........�....
10 00 01 02 02 14 80 07 04 05 00 10 00 01 02 02 ......�.........
[Code].....
first post here at the forums. I am a complete noob when it comes to VB .Net, but I have done a lot of VBA programming and some VB6 back in the day. I have posted this question on two other forums (including the MSDN forums) and no one has responded so please let me know if I need to clarify the question.
I am (trying) to write my first .net app which reads/writes data to a device connected over the serial port. I have manged to get it to work to send commands to the device and receive the reply back, mainly using the info from this article: Beth Massi - Sharing the goodness that is VB : Reading from a Serial Port and Saving to a Database
However, I am having problems with updating the controls on the main form based on the received data from the serial port. Basically I want the user to click a button (one of six on the form) which will send data to the device, then based on the response from the device, the BackColor of that particular button, will be changed accordingly. I just am missing something b/c the button click is a different sub than the sub that handles the form controls update and I can't get the two to talk
[Code]...
Recently we have connected one bluetooth device which receive data from our serial device. The bluetooth device further transmite this data to a Windows Mobile which is bluetooth enable. Baud rate of whole system is 19200 with 7 data bit and 1 stop bit.When we send command to serial device through bluetooth device it is accepting the command and respond accordingly. but some of data byte of string is desplay as question mark (?).But in case we connect the serial device directly to PC, the string received is correct.[code]Response given by Serial Port is "?09?D03?A D?
View 1 RepliesRecently we have connected one bluetooth device which receive data from our serial device. The bluetooth device further transmite this data to a Windows Mobile which is bluetooth enable. Baud rate of whole system is 19200 with 7 data bit and 1 stop bit.When we send command to serial device through bluetooth device it is accepting the command and respond accordingly. but some of data byte of string is desplay as question mark (?).[code]...
View 4 RepliesI need to write an application for receiving data (ascii characters) from microcontroller through the serial port in three separate parts. I've created three RichTextBoxes, but I do not know which commands I need to type. In first textbox I need to receive one byte... next six bytes need to be placed in second text box, and finally last seven bytes need to be placed in third textbox.
View 11 RepliesI don't really quite understand how the receiving works but could anyone please help me on how does the receive sms works when using serial port and AT-commands? Here is how I use my code:
Imports System.Windows.Forms.Form
Imports System.Text.Encoding
Imports System.Threading
Imports System.IO.Ports
[Code]...
I am doing a project on receiving the serial port. but the problem is that I am a lost now because I am in the dead end because my project is near the dateline. I am at blank now. Can anyone help me to teach me step by step on how to do the part on receiving sms using the modem?
View 10 RepliesIf I touch the Power & Send wires together on a serial cable the program needs to count up by one. It is just acting as a counter is all.I have some code, but I cannot get it to count....It doesn't even appear to be getting to the SerialPort1_DataRecieved event....ok at this and see what I'm missing? I'm using VB 2010 Express. The serial port properties are all left at default.
Code
Public Class frmMain
Private Sub frmMain_FormClosing(ByVal sender As Object, ByVal e As
[code].....
I am using VB studio 2010 now. What I want to do is to receive data from another port and save it in my directory. However the port can receive my buffer from another port but could not save the file. [Code]
View 14 RepliesI want a text box in my application that will display the data currently coming from the serial port,So if i will send ascii "hello" from another computer on my program it will diaplay "hello".
View 23 RepliesI am currently writing a console code that I will eventually create with a GUI. The problem I am currently having is that when a message I received to the port is an ASCII command code i.e. <BEL> <CR> then rather than printing these messages
it performs the command and I am unable to respond as per when the command is received. Is there a way to alter the code so I can see these messages or at least determine its been sent so I can respond to it?
I can read data from the serial port (GPS receiver). Its just 2 lines of data every 0.5 seconds. Whats the best method to read the data and display it in a TextBox?
If I use:
DLdate = SerialPort1.Readline()
Then I don't get the new line character, and it just over writes on just one line of the TextBox.
Also, should I time the grab of data, or is there a better way? Should I create a buffer, and when the buffer is full then do a write?
i'm designing this window application wherby it has to get the data from serial port and new data will be display at the textbox.my textbox namely textbox1, textbox2.. till 20.so when 1st data comes in, it will be place to textbox1 then when 2nd data comes in, it will be place at textbox2 and so on.
Now. Should i place the data as array and do textbox array or is there a way to put the data as the for loop runs?i've tried using for loop and textbox + 1 but its not working.
I am currently sending data via a serial port to an AVR microcontroller. I've tried searching the forums here first but haven't found any posts that specifically deal with what I'm trying to do. Here's some additional information that might help before proceeding:
Sendbox = textbox
ReceiveBox = listbox
ReceiveChk = checkbox
I currently have it setup so I enter hex data in Sendbox, click the button, it sends the data to the AVR micro via the serial port, which gets repeated back through the serial port and receives the hex data in the ReceiveBox. I want to be able to setup something similar so I am able to input data into a textbox as binary and have it sent to the AVR that way.
I realize it will send the same data whether I enter it in hex or binary form. I just want the option of being able to send it in either form.
Below is my code.
Private Sub Button1_Click(ByVal sender As System.Object, ByVal e As System.EventArgs) Handles SendButton.Click
SerialPort1.Open()
[Code]....
[code]...
I have a quick question regarding the serial port and timer tick event. Basically i have a micro processor connected to the PC via the serial port. With a baurd rate of 38400 set.When the PC sends the micro ":K + VBCRLF" the micro response with a string of information (ASCII encoded) and delimited with a "," and at the end of the transmission a cartridge return line feed is added.Example of sent string:
"12,1134,123,545,76,6868,34,232,1,2,3,6,7,8" These numbers are then split using the VB mystring.split(",") function into an array of strings, then the numbers are converted using ctype. After which my UI is then updated.I have Witten the code in a tick timer event using a timer count of 300ms. Although the program runs and the UI is updated i end it with lots of exception errors. I think allot of this is down to the serial port either timing out or not reading complete string.Or possibly the timer has not executed all the code before another tick event happens Even after adding a few try catch statements i am still having problems. Can anybody suggest a better way of doing it?I was thinking of using a do while loop and at the end a sleep function instead of the timer tick event.I need the speed as i am trying to read and display live data.
[code]...
i am a absolute beginner and i want to use vb to receive data from micro controller through serial port using rs232 standards, i found this code to receive the data serially, can any one tell me where should i paste this code, so that the data received will be displayed in message box.Private Sub DataReceived(ByVal sender As System.Object, ByVal e As System.IO.Ports.SerialDataReceivedEventArgs) HandlesSerialPort1.DataReceived
[Code]...
I'm mohammed from Oman ,I'm visual studio.net programmer How I can Read the Data From Barcode Weight scales By Serial port and TcpIp port
View 7 RepliesI have a program that receives serial data from a microcontroller and displays it.If I use windows terminal I get the right data.For some reason my program is not displaying the right data.What is sent is temperature.So the actual data is 24 degreesC and my program is showing 10 degreesC.
Private
Sub SerialPort1_DataReceived(ByVal sender As Object, ByVal e As System.IO.Ports.SerialDataReceivedEventArgs) Handles SerialPort1.DataReceived
[code]....
I have a very basic knowledge of coding, just enough to understand some PicBASIC Pro and program a microchip to send the values of some variables to a PC via the com port. I've used a terminal utility like Hyperterm to confirm the right variables are being sent, so I thought it would be cool to have a custom application on the PC to display these variables, and possible set them via the application by writing the new one back to the PIC. So I downloaded VB express 2008 - and whilst it was "simple" to draw a box and add a few text boxes I'm lost at how to actually do anything practical with it
[Code]...
Could someone advise me in laymens terms exactly what I need to do inorder to populate the text boxes with the data from the PIC micro. Whilst I understand the basics about BASIC, I have no idea on things like classes etc
I'm trying to read a string(what's going on) from my Arduino and display it in either a label or text box. but its not wanting to display the characters, or string i want it to. So I could really Here's the code I have right now:
Imports System.IO
Imports System.IO.Ports
Imports System.Threading
[code].....
I'm working on a project involving reading RFID tags, I've written the code and it reads the tags ok by using the recieved data handler and displaying the result in a listbox, the only problem is that the data displayed has a couple of unreadable characters at the start (I'm using ReadLine() command.)If I read the buffer byte by byte the data is all readable.How can I read and display the whole 16 Bytes in one go??
View 3 RepliesThe link below has code to connect to a modem thru the serial port but it is for an earlier version of VB. when I convert the code, it does not fully convert and has 4 errors that prevent building the project. can someone tell me what needs to be changed or added?
[URL]
Note: the error: not CLS-Compliant
I am facing problem reading data from Serial port. Actually I am connecting with the hardware device called Crimp Force Analyzer. It gives the data on hyperterminal and I have to read that data from my <acronym title="Visual Basic">vb</acronym>.net program. The data is somewhat like this:
[Code]....