Receiving Invalid Data From Serial Port Using SerialPort.ReadExisting()
Jan 16, 2010
Recently we have connected one bluetooth device which receive data from our serial device. The bluetooth device further transmite this data to a Windows Mobile which is bluetooth enable. Baud rate of whole system is 19200 with 7 data bit and 1 stop bit.When we send command to serial device through bluetooth device it is accepting the command and respond accordingly. but some of data byte of string is desplay as question mark (?).[code]...
View 4 Replies
ADVERTISEMENT
Jan 16, 2010
Recently we have connected one bluetooth device which receive data from our serial device. The bluetooth device further transmite this data to a Windows Mobile which is bluetooth enable. Baud rate of whole system is 19200 with 7 data bit and 1 stop bit.When we send command to serial device through bluetooth device it is accepting the command and respond accordingly. but some of data byte of string is desplay as question mark (?).But in case we connect the serial device directly to PC, the string received is correct.[code]Response given by Serial Port is "?09?D03?A D?
View 1 Replies
Nov 30, 2008
i was not getting o/p properly when i tried to receive data from serial port using the following code.
Public Class form1
Private Sub Timer1_Tick(ByVal sender As System.Object, ByVal e As System.EventArgs) Handles Timer1.Tick
If SerialPort1.IsOpen Then
[code]....
View 4 Replies
Aug 13, 2009
I'm trying to control a serial port device that both send and receives data. I can receive data quite happily from the serial port but I don't appear to be able to send data to the device. The device works perfectly as I can test it using putty, I open putty select serial and select 1200 baud, the device immediately lights up and can send and receive. However when the port is set up and opened in VB the device doesn't light up so I can't send data to it but can receive data from it. According to the instructions I need to send either ASCII 'X' Hex '$58' or Decimal '88' to make the device ready.
Code (VB Studio 2005) :-
Public Sub New(ByVal synchronisingObject As ISynchronizeInvoke)
ComPortUsed = My.Computer.Registry.GetValue("HKEY_LOCAL_MACHINESoftwareNJB", "COMUSED", Nothing)
PricePerTrack = My.Computer.Registry.GetValue("HKEY_LOCAL_MACHINESoftwareNJB", "PRICETRACK", Nothing)
Me.synchronisingObject = synchronisingObject
[Code] .....
View 11 Replies
Feb 22, 2011
Opening and closing the port works fine, and as far as i can tell, the serial.write("blahblah") should be writing to the output buffer, but I am unable to test or verify this by reading it in. the commented "Receive data from serial port" and subsequent DoUpdate() function are where i am having trouble. It doesnt seem to actually be reading in the data if it is in fact writing it correctly.
[Code]...
View 9 Replies
Dec 20, 2009
What I am doing is creating an app to send and receive CNC programs to machine tools via the RS232 interface. At the moment I am testing the software with 2 laptops linked together through a cable I have made up. which all works. I have added a serial port to my form 1 and using the code below I can send and receive data. However with the send button I can open the comm port send the data and then close the comm port (No Problems there). With the receive button I want to open the comm port receive the data and close the comm port. The problem I have is checking when the app has finished receiving data so I can then close the comm port
Private Sub Btn_Send_Click(ByVal sender As System.Object, ByVal e As System.EventArgs) Handles Btn_Send.Click
Try
[Code]....
View 2 Replies
May 11, 2011
I have serial port object which continuously receiving data from weighing device, which sends data in 0001450= format (8 Bytes). I read about datareceived event, and implement that, but i must use Thred.Sleep to get all data and read with serial.ReadExisting. Does the ReadBytesTreshold=8 raised DataReceived event after 8 bytes of data??
Is there any way to cancel, abort, stop DataReceived event?
View 4 Replies
May 30, 2012
i'm using serial port monitor 4.0. i need to know how to received the data and show in a textbox.
here is how my data look like in the serial port monitor:
40 03 04 05 00 00 00 80 05 04 01 00 00 00 11 00 @......�........
80 07 04 05 00 10 00 01 02 02 14 80 07 04 05 00 �..........�....
10 00 01 02 02 14 80 07 04 05 00 10 00 01 02 02 ......�.........
[Code].....
View 9 Replies
Feb 13, 2009
first post here at the forums. I am a complete noob when it comes to VB .Net, but I have done a lot of VBA programming and some VB6 back in the day. I have posted this question on two other forums (including the MSDN forums) and no one has responded so please let me know if I need to clarify the question.
I am (trying) to write my first .net app which reads/writes data to a device connected over the serial port. I have manged to get it to work to send commands to the device and receive the reply back, mainly using the info from this article: Beth Massi - Sharing the goodness that is VB : Reading from a Serial Port and Saving to a Database
However, I am having problems with updating the controls on the main form based on the received data from the serial port. Basically I want the user to click a button (one of six on the form) which will send data to the device, then based on the response from the device, the BackColor of that particular button, will be changed accordingly. I just am missing something b/c the button click is a different sub than the sub that handles the form controls update and I can't get the two to talk
[Code]...
View 5 Replies
Apr 28, 2012
I ve been reading forums all over the net for 2 weeks and I failed to find solution for my problem. here is my problem;
I am able to receive data from serial port in to richtextbox and its working fine .. what i wanna do is dislay data in textbox by spliting string[code]...
View 5 Replies
Jun 10, 2010
I am developing an test application to read the data coming on serial port sent by the pabx. It is working fine. But, for some reason , i don't know why, some invalid characters are coming in the data, something like '?'
[Code]...
View 1 Replies
Jul 18, 2009
I need to write an application for receiving data (ascii characters) from microcontroller through the serial port in three separate parts. I've created three RichTextBoxes, but I do not know which commands I need to type. In first textbox I need to receive one byte... next six bytes need to be placed in second text box, and finally last seven bytes need to be placed in third textbox.
View 11 Replies
Aug 5, 2009
I don't really quite understand how the receiving works but could anyone please help me on how does the receive sms works when using serial port and AT-commands? Here is how I use my code:
Imports System.Windows.Forms.Form
Imports System.Text.Encoding
Imports System.Threading
Imports System.IO.Ports
[Code]...
View 21 Replies
Jun 28, 2010
I am doing a project on receiving the serial port. but the problem is that I am a lost now because I am in the dead end because my project is near the dateline. I am at blank now. Can anyone help me to teach me step by step on how to do the part on receiving sms using the modem?
View 10 Replies
Sep 19, 2011
If I touch the Power & Send wires together on a serial cable the program needs to count up by one. It is just acting as a counter is all.I have some code, but I cannot get it to count....It doesn't even appear to be getting to the SerialPort1_DataRecieved event....ok at this and see what I'm missing? I'm using VB 2010 Express. The serial port properties are all left at default.
Code
Public Class frmMain
Private Sub frmMain_FormClosing(ByVal sender As Object, ByVal e As
[code].....
View 1 Replies
Sep 10, 2011
I am using VB studio 2010 now. What I want to do is to receive data from another port and save it in my directory. However the port can receive my buffer from another port but could not save the file. [Code]
View 14 Replies
Jul 14, 2010
I am currently writing a console code that I will eventually create with a GUI. The problem I am currently having is that when a message I received to the port is an ASCII command code i.e. <BEL> <CR> then rather than printing these messages
it performs the command and I am unable to respond as per when the command is received. Is there a way to alter the code so I can see these messages or at least determine its been sent so I can respond to it?
View 5 Replies
Sep 9, 2010
I have things set up so that the program is ready to start logging ,only when Recieving=true.This is controlled with Button1. So I click button1,Serial port is open and waiting for some signals from the Dyno.When 1 signal come it put a "1" in TextBox1 ,and for the second a "2" and so on. Thing is sometimes it starts right away, like I want it to,and sometimes it lags a fraction of a second, even though the Port is open.When it lags there are already 5 to 10 signals gone by before it starts logging 1,2,3,...and so on. Sometimes it don't start at all.Then I have to close and re-open the form and it works,but with lagging on the first "set"
"Textbox1 > 0 then" triggers a timer (not seen in this code)that samples Textbox1 once pre interval and writes the value to a listbox. On the upside as soon as a "1" is displayed in textbox1 the timer starts like it's supposed to.I noticed this behaviour before I added the timer and besides the timer has nothing to do with the signals coming from the SerialPort. I have my form setup so I can run "sets".Run one "set"...save...reset...run another "set" ...and compare.It's always the first "set" thats off.If I run multiple "sets" the first one is completely "whacked", and the rest are consistent.
Think this could be the SerialPort lagging,or code problems?
Public Class Form1
Dim resetValues As Boolean = False
Dim RPM As Double
[CODE]...
View 19 Replies
Mar 10, 2010
I'm using the following to read a serial port. When run it displays the data correctly but stepping through the program I find that it loops through the serialdatarecieved event for each character of the port input rather than reading all of it. So _msg only equals one letter at a time. I'm trying to set a variable equal to the entire input stream but only get one character of it.The end goal is to capture all of the data available on the port when the event triggers so that this data can then be processed. I tried using the bytestoread function, which gets the correct number of bytes to read, and then looped through to read a byte at a time but that didn't seem to work as I expected either. It just kept reading the first byte.
Imports System.IO.Ports
Public Class CommTest
Dim WithEvents SerialPort As New SerialPort
[code]....
View 3 Replies
Jan 31, 2012
I'm trying to make a simple Class that reads data from a SerialPort.The Device returns a number of lines of Strings.
Code:Public Class Device
Private Device As New IO.Ports.SerialPort("COM4", 4800) Private WithEvents tmr As New Timer Public Event GotData(ByVal Data As String)
[code].....
View 5 Replies
Jun 27, 2011
i try readexisting and instr function as follow:
[code]...
View 1 Replies
Apr 5, 2010
i'm using the AppendText(serialPort.ReadExisting) method of the SerialPort class. i'm sending to the serial port a 12 byte frame. however in the TextBox control streams printed seem choppy as if the ReadExisting method is exiting too quick to grab all 12 bytes so i can display them at once.
View 3 Replies
Aug 16, 2011
i am a absolute beginner and i want to use vb to receive data from micro controller through serial port using rs232 standards, i found this code to receive the data serially, can any one tell me where should i paste this code, so that the data received will be displayed in message box.Private Sub DataReceived(ByVal sender As System.Object, ByVal e As System.IO.Ports.SerialDataReceivedEventArgs) HandlesSerialPort1.DataReceived
[Code]...
View 9 Replies
Nov 27, 2010
I'm mohammed from Oman ,I'm visual studio.net programmer How I can Read the Data From Barcode Weight scales By Serial port and TcpIp port
View 7 Replies
Dec 13, 2009
I have a program that receives serial data from a microcontroller and displays it.If I use windows terminal I get the right data.For some reason my program is not displaying the right data.What is sent is temperature.So the actual data is 24 degreesC and my program is showing 10 degreesC.
Private
Sub SerialPort1_DataReceived(ByVal sender As Object, ByVal e As System.IO.Ports.SerialDataReceivedEventArgs) Handles SerialPort1.DataReceived
[code]....
View 8 Replies
Aug 16, 2010
I have a very basic knowledge of coding, just enough to understand some PicBASIC Pro and program a microchip to send the values of some variables to a PC via the com port. I've used a terminal utility like Hyperterm to confirm the right variables are being sent, so I thought it would be cool to have a custom application on the PC to display these variables, and possible set them via the application by writing the new one back to the PIC. So I downloaded VB express 2008 - and whilst it was "simple" to draw a box and add a few text boxes I'm lost at how to actually do anything practical with it
[Code]...
Could someone advise me in laymens terms exactly what I need to do inorder to populate the text boxes with the data from the PIC micro. Whilst I understand the basics about BASIC, I have no idea on things like classes etc
View 5 Replies
Aug 13, 2010
I am writing a small app that is retrieving data from a device connected to a virtual com-port. I connect without problems to the device using the settings 9600-8-N-1.
I need to send the command <esc>MS , the device then sends back the data to a computer. I have tried this using Hyperterminal with success. I also did this with Excel and VBA. I used the MSComm32 Active X control:
MSComm1.Output = Chr$(27) + "M" + "S" + Chr$(13)
Msgbox(MSComm1.Input)
This made the data from the device pop up in a messagebox. I am writing a winforms app in vb.net, using VS2005. I have a form, on which I have a Placed a SerialPort control, named sp. My sample code is as follows:
Private Sub Form1_Load(ByVal
sender As System.Object,
ByVal e
[CODE]...
This returns the error message "Error: expecting a command". I have done som tests in HyperTerminal, and have concluded with:
-If I dont send <esc>, I get error "Expecting a command"
-If I send wrong command (ie MD instead of MS) i get error "Bad command"
Based on this, I suspect that I don't pass the escape character correctly to my device. So I wonder how to do this?
View 5 Replies
Oct 26, 2011
The link below has code to connect to a modem thru the serial port but it is for an earlier version of VB. when I convert the code, it does not fully convert and has 4 errors that prevent building the project. can someone tell me what needs to be changed or added?
[URL]
Note: the error: not CLS-Compliant
View 8 Replies
Jan 30, 2011
I am facing problem reading data from Serial port. Actually I am connecting with the hardware device called Crimp Force Analyzer. It gives the data on hyperterminal and I have to read that data from my <acronym title="Visual Basic">vb</acronym>.net program. The data is somewhat like this:
[Code]....
View 8 Replies
Nov 10, 2009
I'm currently working on a project where I am transmitting data from a comm device via the serial port and resorting the raw data (in binary) to its respective ascii values. The problem I'm facing is determining the most efficient method to accomplish my goal. Essentially, I have 68 bytes coming in, the first and second bytes represent the page and packet number and the data itself ranges from 3 to 64, the remaining for my checksum.
What I am needing to do is, grab 50 consecutive bytes per variable in my array, and that is where I'm confused. I have easily pulled my 3-64 bytes and stored that data to a string. I just don't know the most efficient method to accomplish my goal. Should I write directly to file all my data, as there are like 8 pages, of 128 packet data. [Code] I can capture the the first 50 by using a for-loop easily, but what would be the preferred method to track what data chunk I've taken? The more I think about it, I think I may just want to write to file, all my data, and then just take them back to back in 50 byte chunks. Is that the most efficient method?
View 3 Replies
