Send Serial String Out RS-232 And Notify
May 9, 2010
My code below works as far as sending the commands to com1 (not sure if this is best method however) but when I try to move 'sending' to Label2 to tell the operator to wait it doesnt do it?? The Label2.Text = "" does work and clears the text that is in the properties for the label after codes sent. Why? The debugger stops on this line like it should... I am brand new to programming so go easy
[Code]...
View 6 Replies
ADVERTISEMENT
Aug 5, 2010
I am trying to send a control string from VB.NET to a serial port. I am using a pololu trex jr. on the receiving end of the serial port. I have attached a copy of my current code which compiles without errors, but fails to send data. I can tell that it is not sending data because I have a light on the control board connected to the port and it normally blinks when data is received. The program that came with the board drives it perfectly but does not serve the purpose I need it to. I am open to any suggestions as I eventually plan to write a class to contain the control routines.
View 12 Replies
Mar 11, 2010
i knew Serial ports are a type of computer interface that complies with the RS-232 standard. They are 9-pin connectors that relay information, incoming or outgoing, one byte at a time. Each byte is broken up into a series of eight bits, hence the term serial port.And I want to write a program chatting through Serial Port.
View 3 Replies
Apr 18, 2012
im very new to visual basic. as in i just started 2 days ago. Currently i have a little program written up that has a couple of radio buttons and then a submit button. when you select a radio button and click the submit button, a little message box with pop up and say "you selected such and such"
Well now im trying to make something that will send a string to arduino through the usb cable. Basically it will use the same set up as stated above but instead of a pop up message it will just send the string through the port. for example Radiobutton1 - when selected and submit button pressed will send "1" (no quotes) through the serial port Radiobutton2 - when select and submitted will send "1" and then maybe "3"
and so on and so. Some radio buttons will only send 1 string through them and some may send multiple. Now, i dont need help with arduino, i have that already set up to wait for the strings to come through the com port. just need to figure out how to do it in VB.
View 1 Replies
Sep 20, 2010
In VB6, I use CHR$(&H00) to create a Null Character. In VB.Net VS2008 CHR(&H00) creats a Null. I'm trying to send a Hex(00) to a serial device, but the VB.Net function only sends a null, not a null character. How can I accomplish this with VB.Net?
View 5 Replies
Sep 20, 2010
In VB6, I use CHR$(&H00) to create a Null Character. In VB.Net VS2008 CHR(&H00) creats a Null. I'm trying to send a Hex(00) to a serial device, but the VB.Net function only sends a null, not a null character. How can I accomplish this with VB.Net?
View 1 Replies
Sep 11, 2009
sending a hex file through serial port using vb.net? and i m not really sure the difference between sending data and sending a file, seems majority of the topics on the forum is about sending data via serial port.
View 2 Replies
Mar 11, 2010
I am trying to send a ctrl-x keystroke to COM2 and I ahve to code to open the port and read and write but when I tried to send Chr(Keys.ControlKey + Keys.X) it did not work
View 1 Replies
Feb 18, 2011
I used this code in the pass with VB6 to send hex data over the serial port to a microcontroller.
MSComm1.Output = "C"
Send command ID
MSComm1.Output = Chr$("1") Send Command Parameter
MSComm1.Output = Chr$(CStr(240)) Send CR
I need to convert the code using VB2010, but Chr$ is not available, and anything I tried will not send the actual ascii code character......
View 10 Replies
Jul 8, 2011
I have created a program to send and receive data from a serial port, some of the data needs to be stored in certain strings for a export to excel. However the data takes while to to send be sent back. So in order to get the right information in the right strings I have to put pauses in my code. I have added a timer to my form:
On my timer's tick event I have the following code:
Public Sub Timer1_Tick(ByVal sender As System.Object, ByVal e As System.EventArgs) Handles Timer1.Tick
iTick = iTick + 1
End Sub
View 3 Replies
Jul 18, 2011
I want to send hex values across the serial port. I know, I know, your thinking not this again. But what I need to do does not seem to be addressed, or I am some how missing it when I search around.
[Code]...
View 2 Replies
Dec 8, 2010
I've set up two computers, with a null modem serial cable. When trying the connection in two Realterm windows it works ok to send strings.I'm trying to write a simple project that sends the timestring over the same port.One button sends the timestring. I've created one other sub "AppendLabel" that just updates a label.text so I can see what's happening.[code]
View 8 Replies
Dec 1, 2011
I have quite a bit of VB6 experience but now am trying to create my first VB.Net project. The project is very simple - it just needs to send 8-10 character strings from the PC serial port. The problem I'm seeing is that VB.Net is always sending out a 0x0A character after each 'WriteLine' call. Using VB6 it was necessary to manually send out any End Of Line characters. My application requires that no extra EOL characters be sent after the string.
View 2 Replies
Nov 9, 2009
I need to send data via serial and wait for and answer (VB.NET).Right now i'm doing it this way:SerialPort1.Write(sel & Chr(13))Thread.Sleep(50)aaa = SerialPort1.ReadExisting()If i do not thread.sleep, i get nothing, i supose it's because the machine is too fast.
View 1 Replies
Feb 24, 2011
I am supposed to make a software for data logging via serial port but the hardware is expected to be delayed and iam required to continue with the programming of the software. What i need is that by some mechanism i want to send data on serial port (COM port) and after delay of some mili seconds i want to detect that data. I actually want to do this because i want to create environment like my software i intercepting COM port and on receiving data it captures the data values on port and record them to database. I have done most the work, the only thing left which i want is as above how i will send data on COM port (this was to actually to be done by hardware) and detect it in my program (same program from which data was sent). Please guide from where should i start.
View 3 Replies
May 5, 2011
How do I send XML commands in vb to get data received over a serial Port?
I know the commands I'm just not sure how to send them.
View 2 Replies
Sep 1, 2009
I am currently sending data via a serial port to an AVR microcontroller. I've tried searching the forums here first but haven't found any posts that specifically deal with what I'm trying to do. Here's some additional information that might help before proceeding:
Sendbox = textbox
ReceiveBox = listbox
ReceiveChk = checkbox
I currently have it setup so I enter hex data in Sendbox, click the button, it sends the data to the AVR micro via the serial port, which gets repeated back through the serial port and receives the hex data in the ReceiveBox. I want to be able to setup something similar so I am able to input data into a textbox as binary and have it sent to the AVR that way.
I realize it will send the same data whether I enter it in hex or binary form. I just want the option of being able to send it in either form.
Below is my code.
Private Sub Button1_Click(ByVal sender As System.Object, ByVal e As System.EventArgs) Handles SendButton.Click
SerialPort1.Open()
[Code]....
View 1 Replies
Apr 12, 2009
I have a USB modem that can detect caller ID and can detect dialled digits when special AT commands activated, How to send and receive data. The sent data will be the AT command such as AT+VCID-1 to activate the caller ID, the received data will be caller ID information and the digits dialed. I'm new to prgramming and using Visual Basic 2008 Express.
View 8 Replies
Jun 22, 2010
I got an app, which receives data via a R232 port, convert it to a string and on the other side I got a database, where the strings are saved. How can I find a way to compare the string with all strings in one database column and get back the another stringform the same row in this database. I never programmed a database
View 1 Replies
Nov 14, 2011
I m writing serial port program i can send hex data without any problem but i stuck when I get response in buffer for example response is a string "?-??"
[Code]...
View 22 Replies
Oct 22, 2009
For starters I'm using VB 2008 express edition.I have code that writes a string out of a serial port.My issue is that the machine sends data back and I don't know how to catch it.This is my latest attempt at creating an array of characters to create a string later but doesn't work.[code]
View 2 Replies
Mar 2, 2010
I do not have much experience with VB.What I need to do is to read a serialport as a hexadecimal string.I've done this with the MSCommlib, but now want to convert to system.io.ports.The equipment wich is connected to the serialport is a RFID card-reader, so the application haft to detect when it is receveing data, and then continue on.[code]
View 5 Replies
Jan 22, 2010
i am working on my collage project in which i have an "sensor" which detects weights.specifications : (COM1,2400,N,8)I have added two components Timer and Serialport and set the values timer duration =1000 and added a button and textbox.when user clicks on the button timer1 gets started.and in timer1 i added th code which reads the input from serial.now the problem with the code. the input which i eceive is in ASCII formats(actually some of chars are in ascii format).This is the output i m getting :- 029990so i created a string variable which stores this value.
actually i want only number from that string
ex : 029990 ===> 029990
but i m unable to retrieve that.
[code].....
View 2 Replies
Jun 9, 2009
I have an application in Electronics to communicate with serial port. With using VB I have succesfully read a character using
Serialport1.ReadByte
or
Serialport1.ReadChar
[code].....
View 5 Replies
Dec 19, 2011
I'm trying to read a string(what's going on) from my Arduino and display it in either a label or text box. but its not wanting to display the characters, or string i want it to. So I could really Here's the code I have right now:
Imports System.IO
Imports System.IO.Ports
Imports System.Threading
[code].....
View 14 Replies
Apr 26, 2012
I'm new to VB, I'm now want to know how to convert received string to double. I'm receiving string like this 420.8 280.9 140.2 from serial port.. and transferred it into textbox.. I'm using following code to split string and to convert to double
[Code]...
View 1 Replies
May 6, 2010
i want to generate a serial key which depend on system harddisk manufacture id ...
so Is any function which take string of alfanumeric + special char as input and after encrypted return output as unique serial key / product key...
View 10 Replies
May 7, 2009
I have made a small program displaying a string value coming from a serial device. When I run this on my laptop, then everything is just fine (VISTA OS), but when I run the same program on another computer (XP OS), then it shows some strange chars (Squares in distance number).
View 8 Replies
Sep 21, 2010
I've inherited a tested function that processes incoming data from a .NET Serial Port. (Dim RXBuffer as string = serialport1.ReadExisting) I've written a different part of the application that processes a byte array as received from an asynchronous .NET socket.
Is there a way I can convert the byte array into a string as if it arrived from the serial port?
I would prefer to rewrite a very long 'if statement' into byte array functions syntax that look like:
dim b as boolean = IsBitSet(state_buffer(i), j) 'rather than:
dim b as boolean = (Asc(Mid(RXPacket.Pdu, CInt((i - (i Mod 8)) / 8) + 1, 1)) And CInt(2 ^ (i Mod 8))) > 0
View 3 Replies
May 16, 2009
I made my program and now I just need to add in the serial and trial part of the application. I know the application must connect to the host and go to a txtfile. How would i do the trial and serial. Also If the serial is already activated I want the application to reject that Serial and Count how many times they entered in a wrong serial.
View 2 Replies